Improve network latency for Linux based Amazon EC2 instances
Network latency is the amount of time it takes for a packet of data to travel from its source to its destination. Applications that send data across the network depend on timely responses to provide a positive user experience. High network latency can lead to various issues, such as the following:
-
Slow load times for web pages
-
Video stream lag
-
Difficulty accessing online resources
This section outlines steps that you can take to improve the network latency on Amazon EC2
instances that run on Linux. To achieve optimal latency, follow these steps to configure
your instance, kernel, and ENA driver settings. For additional configuration guidance, see
the ENA Linux Driver Best Practices and Performance Optimization Guide
Note
Steps and settings may vary slightly, depending on your specific network hardware, the AMI that you launched your instance from, and your application use case. Before you make any changes, thoroughly test and monitor your network performance to ensure that you're getting the desired results.
Reduce network hops
Each hop that a data packet takes as it moves from router to router increases network latency. Typically, traffic must take multiple hops to reach your destination. There are two ways to reduce network hops for your Amazon EC2 instances, as follows:
-
Cluster placement group – When you specify a cluster placement group, Amazon EC2 launches instances that are in close proximity to each other, physically within the same Availability Zone (AZ) with tighter packing. The physical proximity of the instances in the group allows them to take advantage of high-speed connectivity, resulting in low latency and high single flow throughput.
-
Dedicated Host – A Dedicated Host is a physical server that's dedicated for your use. With a Dedicated Host, you can launch your instances to run on the same physical server. Communication between instances that run on the same Dedicated Host can happen without extra network hops.
Linux kernel configuration
Linux kernel configuration can increase or decrease network latency. To achieve your latency optimization goals, it's important to fine-tune the Linux kernel configuration according to the specific requirements of your workload.
There are many configuration options for the Linux kernel that might help decrease network latency. The most impactful options are as follows.
-
Enable busy poll mode – Busy poll mode reduces latency on the network receive path. When you enable busy poll mode, the socket layer code can directly poll the receive queue of a network device. The downside of busy polling is higher CPU usage in the host that comes from polling for new data in a tight loop. There are two global settings that control the number of microseconds to wait for packets for all interfaces.
busy_read-
A low latency busy poll timeout for socket reads. This controls the number of microseconds to wait for the socket layer to read packets on the device queue. To enable the feature globally with the sysctl command, the Linux Kernel organization recommends a value of 50 microseconds. For more information, see busy_read
in the Linux kernel user's and administrator's guide. $sudo sysctl -w net.core.busy_read=50 busy_poll-
A low latency busy poll timeout for poll and select. This controls the number of microseconds to wait for events. The recommended value is between 50-100 microseconds, depending on the number of sockets you're polling. The more sockets you add, the higher the number should be.
$sudo sysctl -w net.core.busy_poll=50
-
Configure CPU power states (C-states) – C-states control the sleep levels that a core may enter when it's inactive. You might want to control C-states to tune your system for latency versus performance. In deeper C-states, the CPU is essentially "asleep" and can't respond to requests until it wakes up and transitions back to an active state. Putting cores to sleep takes time, and although a sleeping core allows more headroom for another core to boost to a higher frequency, it takes time for that sleeping core to wake back up and perform work.
For example, if a core that's assigned to handle network packet interrupts is asleep, there might be a delay in servicing that interrupt. You can configure the system so that it doesn't use deeper C-states. However, while this configuration reduces the processor reaction latency, it also reduces the headroom available to other cores for Turbo Boost.
To reduce the processor reaction latency, you can limit deeper C-states. For more information, see High performance and low latency by limiting deeper C-states in the Amazon Linux 2 User Guide.
ENA driver configuration
The ENA network driver enables communication between an instance and a network. The driver processes network packets and passes them on to the network stack or to the Nitro card. When a network packet comes in, the Nitro card generates an interrupt for the CPU to notify the software of an event.
- Interrupt
-
An interrupt is a signal that a device or application sends to the processor. The interrupt tells the processor that an event has occurred or a condition has been met that requires immediate attention. Interrupts can handle time-sensitive tasks such as receiving data from a network interface, handling hardware events, or servicing requests from other devices.
- Interrupt moderation
-
Interrupt moderation is a technique that reduces the number of interrupts a device generates by aggregating or delaying them. The purpose of interrupt moderation is to improve system performance by reducing the overhead associated with handling a large number of interrupts. Too many interrupts increase CPU usage, impacting the throughput adversely, while too few interrupts increase the latency.
- Dynamic interrupt moderation
-
Dynamic interrupt moderation is an enhanced form of interrupt moderation that dynamically adjusts the interrupt rate based on the current system load and traffic patterns. It aims to strike a balance between reducing interrupt overhead and packets per second, or bandwidth.
Note
Dynamic interrupt moderation is enabled by default in some AMIs (but can be enabled or disabled in all AMIs).
To minimize network latency, it might be necessary to disable interrupt moderation. However,
this can also increase the overhead of interrupt processing. It's important to find the
right balance between reducing latency and minimizing overhead. ethtool
commands can help you configure interrupt moderation. By default, rx-usecs
is set to 20, and tx-usecs is set to 64.
To get the current interrupt modification configuration, use the following command.
$ethtool -cinterface| egrep "rx-usecs:|tx-usecs:|Adaptive RX"Adaptive RX: on TX: off rx-usecs: 20 tx-usecs: 64
To disable interrupt modification and dynamic interrupt moderation, use the following command.
$sudo ethtool -Cinterfaceadaptive-rx off rx-usecs 0 tx-usecs 0
